However some that will fit are late 70's 14" such as torino and ranchero. You will have to look at the offset to determine if they will interfere with the caliper. There are numerous 14" wheels that will work. You cannot however use your stock 14" wheels. With this conversion you do not have to disturb any of your suspension nor steering. Remove everything except for the spindle and the rest is provided. You use your stock spindle and suspension. (I have provided these in the photo to show you what it will look like on your car.) This conversion includes everything you see in the photo EXCEPT the spindle and nut. (photo is of a 1962 spindle installation, all others are very similiar) However the aftermarket Roadster wire wheels will work but you must let me know you are going to use them so that I can turn down the center hub on the rotors to fit the center of the wheel.
Stock Kelsey Hayes wire wheels will not fit The stock 14" wheels cannot be used with this kit. You can find shops and car dealers that offer BG services and chemicals at Brake Conversion Front for 1958 thru 1964 Note: Dip in the DOT 3 or 4 fluid and if the color changes it is time to do a fluid exchange. They might also sell you a container of the fluid test strips they might get from BG. Or buy the hose P/N you see on the drawing. Ask to see their hose so you can measure it. Just find a service shop that offers the BG service using either machine and ask them to order the individual adaptor for you to fit your vehicle, or the whole Completer Kit if necessary. Probably the new kit is the same as the old one.
#1959 thunderbird brakerotors plus
It is not likely to pop off like when putting a hose directly on a small nipple.īelow is a picture of the BG adaptors plus the Completer Kit that includes them and the hose. And the silicone hose they use is semi-clear so you can see bubbles or a color change if it is old and greenish brown. Good if the nipples are rounded or very tight. It provided a larger, more wrench-friendly hex. On my personal vehicles I had a short piece of that hose going into a mayonnaise jar so I could get a good look at the old fluid. It fits tight enough so it will not fall out when bleeding. The other end is a round hole into which you put a silicone hose that came with the machine. In the included PF7 adaptor kit PF9000C (new version is E100-2475) were seven bleeder adaptors to fit fractional and metric bleeder nipples. They have a newer one now, I don't know the P/N. Many years ago when I was a BG rep, the machine was the PF7.
#1959 thunderbird brakerotors professional
The automotive chemical company BG Products sells professional brake fluid exchange machines. Regarding putting wrenches on bleeder nipples, here is a tip. Any advice or suggestions would be most welcome. I was thinking we're all so use to disc brakes these days that maybe I've forgotten that's the way it is with drum brakes. And the brakes stop the car but not suddenly or abruptly. The second question is is it not uncommon for the brake pedal to travel four to six inches or so before engaging? It doesn't go to the floor, I have maybe two inches or so before I'd hit the floorboard. I think the only thing left is the power brake booster, but that's under the dash and I don't want to take on that major job unless I know for sure that is the only thing left that it can be. Without taking the wheels off there is no evidence of leaking wheel cylinders and no leaks coming from the master cylinder. After doing all this I saw no improvement. An odd place to put the bleeder valve so close to suspension parts.Īnyway, the pedal was spongy and went almost to the floor when I started. I tried flared nut wrenches as well as standard open-end wrenches with no luck.
I did not bleed the front wheels because I could not get a wrench on the bleeder valve. Hardly any from the second wheel which tells me I got most of the air out of the lines. This weekend I replaced the master cylinder, adjusted brakes and bled the brakes.
0 kommentar(er)
